如何判定測試材料需要多大電壓可以擊穿

How to determine the test material need much can breakdown voltage

如何判定測試材料需要多大電壓可以擊穿，可以通過材料的介電強度和材料的厚度來判斷，一種材料的介電強度值是一定的，擊穿電壓值和厚度是成正比的，材料越厚，擊穿電壓值會越大，

How to determine the test material need much voltage breakdown， judging by the dielectric strength of the material and the thickness of the material， the dielectric strength of a material is a certain value， the breakdown voltage value and the thickness is proportional to， thicker materials， breakdown voltage value will be greater，

    介電強度是一種材料作為絕緣體時的電強度的量度.它定義為試樣被擊穿時，單位厚度承受的最大電壓，表示為伏特每單位厚度.物質的介電強度越大，它作為絕緣體的質量越好

Dielectric strength is a material used as a measure of strength of electrical insulator. It is defined as the sample breakdown voltage， maximum thickness of affordable units， expressed as volts per unit thickness. The dielectric strength of the material， the better the quality of it as an insulator

若客戶第一次做測試，還是不知道材料的介電強度，但是如何判定測試材料需要多大電壓可

以擊穿呢，以下我司歸納了一般材料需要的擊穿強度值

If the customer to do the first time test， still do not know the dielectric strength of the material， but how to judge the test material need much voltage

以擊穿呢，以下我司歸納了一般材料需要的擊穿強度值

The breakdown， the Division I summarizes the breakdown strength of general material required values

DDJ-10KV(1萬伏)主要用于薄膜材料，丙烯薄膜聚乙烯薄膜.聚酯薄膜，流延聚丙烯薄膜，一般厚度為1-3mm

DDJ-10KV (10000 V) is mainly used for thin film materials， propylene films of polyethylene film. Polyester film， cast polypropylene film， general thickness of 1-3mm

DDJ-30KV(3萬伏)主要適用于橡膠，絕緣漆漆膜，聚氨酯，硫化橡膠等推薦可測厚度2-3mm

DDJ-30KV (30000 V) is mainly used in rubber， insulation paint， polyurethane， rubber etc. recommended measurable thickness 2-3mm

DDJ-50KV(5萬伏)主要用于電纜紙，電容器紙，云母，陶瓷，推薦可測厚度為2-3mm

DDJ-50KV (50000 V) is mainly used for cable paper， capacitor paper， mica， ceramic， recommend measurable thickness of 2-3mm

DDJ-100KV(10萬伏)適用于玻璃，層壓材料，橡膠，樹脂，推薦可測厚度為2-5mm

DDJ-100KV (100000 V) is suitable for glass， laminated materials， rubber， resin， recommend measurable thickness of 2-5mm

DDJ-150KV(15萬伏) 適用于塑料、橡膠、層壓材料、薄膜、樹脂、云母、陶瓷、玻璃、絕緣漆等絕緣材料，推薦可測厚度為1-6mm

DDJ-150KV (150000 V) can be used for plastic， rubber， lamination material， film， resin， mica， ceramic， glass， insulating paint and other insulating materials， recommended measurable thickness of 1-6mm

電壓擊穿強度技術資料

Voltage breakdown strength of technical information

電壓擊穿強度技術軟件功能:

電壓擊穿強度技術軟件功能:

Functions of voltage breakdown strength of software technology:

    01、軟件平臺：WINDOWS窗口操作平臺，界面直觀，便于操作

01， the so